The Bevles PHC32-10INS-A-1L1 Proofing and Holding Cabinet Insulated
Why Use Bevles Proofing Cabinet?
BevLes Combination Holding & Proofing cabinets are all aluminum construction and are available in insulated and non-insulated models. Universal extruded pan supports accommodate a wide variety of pans and screens while see-through Lexan doors with heavy-duty hinges feature positive closing latches and full perimeter gaskets.User-friendly, bottom-mounted controls feature independent heat and humidity adjustment. Temperatures range from 80° to 180°F (27° to 82°C) and the water reservoir holds up to 5 quarts (4.7 liters). Bevles "cast-in" humidity system prevents element burnout while providing added safety for the operator. All BevLes proofing and holding cabinets have a self-draining feature for excess moisture collection below the cabinet base into a standard 18"x26" bun pan - pan not included. Heavy-duty swivel-type plate casters with 5" (127mm.) rubber wheels, two with locks, provided.
Bevles PHC32-10INS-A-1L1 Features
Self-draining feature collects excess moisture into a standard bun pan
(not included) below the base of the cabinet
"Cast-in" humidity system prevents element burnout from water spills and
potential injury from accidental contact with exposed heating element
All aluminum construction
Insulated top, side, and back
Extruded pan supports accept a variety of pans and screens
Removable heating module with separate controls for heat and humidity
Maintains uniform temperature and humidity throughout cabinet
Temperature adjustable from 60°F (15.6°C) to 180°F (82.2°C)
Completely removable interior components for quick and easy cleaning
Heavy-duty plate-type casters with 3" hardneoprene wheels, front two with brakes
120V, 20A, 1PH service
Bevles PHC32-10INS-A-1L1 Specifications
Cabinet, Casters and Electrical
Body: .063 Formed aluminum
1.50" Thick insulation top, sides and back
Door: Clear Lexan® with an extruded aluminum frame
Door Latch and Hinges: Positive action door latch with heavy-duty
stainless steel hinges
Door Gasket: Closed cell foam
Base: .125 Formed aluminum
Rear (Air Duct) Panel: .063 Formed aluminum
20 Amp Switch, and pilot light
Pan Supports: Aluminum pan supports adjustable on 1.50"centers
Cord and Plug: 8' cord with 20A molded plug (NEMA 5-20); 208/230 volt
models provided with cord only
Heavy-duty plate type casters, with 5" hard neoprene wheels; all swivel,
with wheel brakes on front two casters
Heating Module and Controls
Bottom mounted heating unit with a one (1) piece modular drop-in design
blower assembly, easily removable for maintenance and cleaning
Air heating element rated at 1000watts
Humidity heating element rated at 400 watts
5 quart (4.7 liter) cast waterreservoir
Lexan® water reservoir cover
Easy to operate controls feature digital thermostat, variable humidity
control and LED display
All controls are visible and operable from exterior of cabinet
Bevles PHC32-10INS-A-1L1 Options and Accessories
Door hinging
Solid doors
Corner bumpers of gray non-marking vinyl (set of 4)
Additional extruded universal pan supports
Perimeter bumper of gray non-marking vinyl
6" stainless steel legs with adjustable feet for stationary floor
installation*
3" casters with hard neoprene or polyurethane wheels
18" x 26" chrome electroplated wire racks
Cord Guide/Protector: Unique cord guide provides safe and easy routing to
rear of cabinet
* Note: Modifications involving casters or legs may affect the height of
the equipment. Specifications subject to change without notice
From The Manufacturer
Proofing & Holding Cabinet, mobile, undercounter, insulated top, back & sides, (1) clear Lexan® left-hand hinged door, digital thermostat, variable humidity control & LED display, 80° to 180°F temperature range, adjustable aluminum pan supports on 1-1/2" centers accommodate (5) 18" x 26" or (10) 12" x 20" pans, removable heating module, 5 qt. cast water reservoir with cover, 3" swivel plate casters (2 with brakes), aluminum construction, 120v/60/1-ph, 2000 watts, 16.7 amps, 8' cord & NEMA 5-20P, cULus, NSF
The image above may not exactly represent the product
