The Delfield 4472RP Front-Breathing Self-Contained Raised Rail Prep Table
Delfield 4472RP Specification
Exterior Top
Exterior top is one-piece 18-gauge stainless steel with integral 2.12”
(5.4cm) square nosing on the front. Top of unit has openings to accept
1/3-size 4” or 6” (10cm or 15cm) deep pans. Adapter bars and 1/3 pans are
supplied by Delfield. Lid is constructed of 20-gauge stainless steel.
Temperature in top opening to maintain 33°F (1°C) to 41°F (5°C), with pans
recessed 2” (5.1cm) at 86°F ambient room temperature, meeting NSF 7
requirements. Unit will also maintain food safe temperatures at 100˚F
ambient. One 17” x .5” (43.2cm x 1.3cm) polyethylene cutting board
provided.
Dual Level Pan Brackets
Dual level pan brackets allow the pans to be lowered an additional inch in
the unit without tools to provide additional pan temperature holding
performance.
Exterior Back-Bottom and Interior Sides
Exterior back and bottom are two-piece 24-gauge galvanized steel. Exterior
ends are stainless steel.
Interior sides are thermoformed ABS plastic with integral shelf supports.
Base is fully insulated with high-density foamed in place environmentally
friendly, Kyoto Protocol Compliant, Non ODP (Ozone Depletion Potential),
Non GWP (Global Warming Potential) polyurethane.
Refrigeration System
Refrigeration system uses environmentally friendly R290 refrigerant.
Condenser coil and hot gas condensate evaporator mounted on rear of the
cabinet. Evaporator coil is located on the interior rear wall of the
cabinet. Refrigerant flow is controlled by a capillary tube. Cabinet
maintains an interior cabinet temperature of 33°F to 40°F (0°C to 4°C).
ACT Control
Temperature control with adaptive defrost: ACT electronic, solid state
control, mounted on the exterior rear of the cabinet, allows unit to
maintain precise temperatures in heavy duty conditions.
Doors and Casters
Doors have a 22-gauge stainless steel exterior, with thermoformed ABS
plastic interior liner. Cabinet of door models has one adjustable
epoxy-coated wire shelf.
Casters Equipment is mounted on 5” (13cm) diameter plate casters with
front two locking. Equipment clearance above the floor is 2.5” (6cm).
Delfield 4472RP Standard Features
All 4400 Series units are 100% front breathing, which allows the unit to
be pushed against a wall or built into a cabinet or an existing line up
Features Delfield’s exclusive ABS interior (on sides). ABS is extremely
durable - it won’t dent, chip or corrode and is backed by a limited
lifetime warranty
Dual level pan brackets allow the pans to be lowered an additional inch
in the unit without tools to provide additional pan temperature holding
performance
Standard with 17” wide, dishwasher safe polyethylene cutting board
mounted on heavy-duty cutting board brackets
High density foamed in place environmentally friendly, Kyoto Protocol
Compliant, Non ODP (Ozone Depletion Potential), Non GWP (Global Warming
Potential) polyurethane keeps energy costs low
Patented low velocity air screen ensures product stays cold without
drying it out
Durable, rugged stainless steel sides, top and front
Rail accommodates 1/3 size or fractional pans with adapter bars
Standard with 1/3 6” deep stainless steel pans in the rail
Environmentally friendly R290 refrigerant
Integral s/s full length door/drawer handles
Standard on 5” casters for easy cleaning and installation
10’ cord and plug supplied
One epoxy coated wire shelf standard, installed per door section
Electronic temperature control with adaptive defrost
Three year parts and labor warranty and an additional two year
compressor parts warranty
4472RP: Two section with doors, nine 1/3 pan capacity