The Delfield 8132-EFP Drop-In Self-Contained LiquiTec™ Refrigerated Cold
Pans
Why Use Delfield's Drop-In?
Safety and Sanitation
UL and NSF - All Delfield Drop-in products are UL approved and NSF
certified. Which means you can count on safe, consistent construction and
performance every time.
Convenience
Delfield Drop-in products are easy to install into any new or existing
counter. A press fit flange gasket comes pre-installed making the units
ready to drop-in immediately.
Quality
Delfield Drop-in products have an unmatched level of quality. The units
are reliably built by the best in the industry and come standard with a
90-day labor and 1-year parts warranty
Construction
Delfield Drop-in products are constructed with stainless steel tops and
interiors. Cold units are insulated with high-density polyurethane foam
and hot units are insulated with fiberglass.
Refrigeration lines are secured to the liner with stainless steel spot
clips and thermal transfer compound is applied to improve heat transferred
cool the food product better.
LiquiTec Cold Pans
Traditional cold pans are inefficient due to lack of contact between the
refrigeration lines and the interior liner side. LiquiTec takes what is
usually on about 1/16” contact per wrap and magnifies it to 100% contact
on all 5 sides of the interior liner. An eutectic fluid is used to
completely surround the interior liner of the pan. The fluid is harmless
and sealed in by a stainless steel exterior liner. The result is improved
cooling ability that allows the unit to have flush mount pans and still
maintain NSF-7 certified temperatures.
Delfield 8132-EFP Standart Features
High density environmentally friendly,Kyoto Protocol Compliant, Non ODP
(Ozone Depletion Potential) Non GWP (Global Warming Potential)
polyurethane foam insulation throughout unit
Stainless steel top construction
LiquiTec cold pans with eutectic fluid technology
Flush mounted 12” x 20” individual stainless steel wells, run left to
right
8132-EFP: Two 12” x 20” pan capacity
Standard 1/2” stainless steel drain with manifold
Electronic temperature control and expansion valve standard
Non-marring press fit top gasket
Environmentally friendly HFC-404A refrigerant
8’ cord and plug
Stainless steel louver for field installation
One year parts and 90 day labor standard warranty
Delfield 8132-EFP Options & Accessories
Single or double service flip-up sneezeguards
Relocate compressor
Remote refrigeration (specify refrigerant)
Drain valve
230 volt, 50 hertz electrical connection*
* Inclusion of this option will alter electrical specifications of the
unit
Delfield 8132-EFP Specification
LiquiTec Cold Pans with Eutectic Fluid technology
allows food in food pans to be flush with top of counter. Cold pan meets
NSF standard 7; and can be dropped into Delfield Mark 7, Shelleyglas® or
Shelleysteel™ counters or existing counters.
Top : is one-piece stainless steel, with 0.62” (1.6cm)
overhang around perimeter and die stamped 19.87” x 11.87” (50cm x 30cm)
openings with depressed edges. Formed well below each opening is 6.25”
(16cm) deep with 0.5” (1.3cm) stainless steel drain and copper manifold.
Each well, flush with the top, for flush mount pans to accommodate 12” x
20” (30cm x 51cm) pans 4” (10cm) or 6” (15cm) deep supplied by others.
Product temperatures of 33°F (1°C) to 41°F (5°C) are maintained at 86°F
(30°C) ambient room temperature, meeting NSF 7 requirements.
Sides and Bottom are insulated with high-density
environmentally friendly, Kyoto Protocol Compliant, Non ODP (Ozone
Depletion Potential), Non GWP (Global Warming Potential) closed-cell
polyurethane. Exterior housing is galvanized steel.
Refrigeration system system uses HFC-404A refrigerant.
Eutectic fluid is used as the heat transfer medium. Condensing unit is
suspended below the cold pan on a steel frame. Electronic temperature
control is supplied with an ON/OFF switch. Unit is supplied with
expansion valve. A stainless steel louver is provided for field
installation; cutout dimension is 11” x 22” (28cm x 56cm). A second
opening 11” x 22” (28cm x 56cm) at the rear of the cabinet should be
provided at installation to allow for proper air circulation
Electrical system is 115V/60Hz/1Ph with NEMA 5-15P
plug. Units have a toggle ON/OFF switch.