Contactless portable hand sink with water heater is self-contained to
allow safe hand washing and sanitizing in remote locations
FWE A-144 Standard Features
FWE banquet cabinets are constructed for high performance restaurant and
resort banquet operations. Our stainless steel, tubular base frame comes
standard and is engineered to absorb vibration and shock during
transport
Radiant heat system gently surrounds food with a soft and uniform
blanket of heat to maximize a food's appearance, taste, and extend
holding times
Our easy to read, simple to set controls are eye-level and
recessed-protected to maximize durability. They include a full range F/C
thermostat that continuously monitors cabinet temperature even without
power
Heavy-duty “no sag” shelves are removable to facilitate easy and
thorough cleaning
Push/pull handles allow easy maneuvering
A” series' models hold up to 11" plates. “A-XL” series’ models are
available to hold up to 12.375" plates
Place the unit anywhere - all units come with a tri-directional AC cord
pocket for flexible plug placement
FWE A-144 Specifications
CONSTRUCTION. Heliarc welded, single unit construction of stainless
steel; 20 gauge polished exterior, 22 gauge stainless steel interior
with easy-to-clean coved corners. Welded tubular base frame shall be 1"
square, heavy gauge stainless steel tubing, with 10 gauge stainless
steel reinforcing stress plates at corners.
INSULATION. “Ultra-Guard” UG-26 high density fiberglass insulation
throughout; top, back, bottom, sides, and door(s).
HANDLES. Heavy-duty, solid formed 1" x .375" thick; mounted at each end
of unit. Mounting reinforced with stainless steel channel
BUMPER. Solid continuous wraparound aluminum channel, bolted to frame,
with snapin, non-marking vinyl cushion. Full perimeter bumper extends
beyond doors, handles, etc., for added protection. Shall be continuous,
with corner cut-outs to facilitate cleaning.
DOORS AND LATCHES. Flush mounted, stainless steel insulated doors. High
temperature gasket sealed; gasket shall be cabinet mounted. Each door
shall have two (2) heavy-duty edgemount die cast hinges. Single-door
models shall have edgemounted and full grip door latches. Two-door
models shall have edgemounted, magnetic and full grip door latches. The
hinge and latch mountings are reinforced with stainless steel backing
plates.
CASTERS. Maintenance free polyurethane tire casters in a configuration
of two (2) rigid and two (2) swivel with brake. A-120-2, A-144, and
A-180-2 models shall be standard with a caster configuration of two (2)
rigid and four (4) swivel with brake. Casters shall have a reinforced
yoke mounted to 10 gauge caster plate. The caster mounting plate shall
be secured to a 10 gauge stainless steel reinforcing stress plate via
welded in place stainless steel studs. The reinforcing stress plates
shall be welded to the heavy gauge tubular frame of the unit
SHELVES. Triple plated, welded rod-type shelves shall be removable.
Shelves shall be supported by high strength, “no sag” 18 gauge
die-formed stainless steel brackets.
HEATING SYSTEM / CONTROLS. Radiant heat system shall include an Incoloy
nickel-chromium alloy heating element. Controls shall be up-front,
recessed and shall include a full range thermostat adjustable to actual
temperature. Thermostat shall include temperature scale marked in ten
degree increments (F/C) from 90° to 190°F (32° to 88°C). An operational
range thermometer, power supply light and thermostat cycling light are
also included.
ELECTRICAL CHARACTERISTICS. 3 wire grounded tri-directional power cord
and plug, rear mounted for safety. See electrical data chart above for
amperage and receptacle configuration. See electrical chart for models
that require a dedicated circuit.
OVERALL EXTERIOR DIMENSIONS IN. (mm) : 67.75" (1721)h x 28.5" (724) d x
53.75" (1366)w
The image above may not exactly represent the product
