This item is too large for a liftgate. It can be delivered with a loading dock or forklift.
Speeder Dishwasher, conveyor type, high temperature, no booster, two-tank with power wash & prewash section, CrossFire® wash system, approximately 277 racks/hour capacity, stainless steel frame, legs & feet, electric immersion or steam injector tank heat
Insinger SPEEDER 86-3 RPW 85" Conveyor Type Dishwasher
Insinger SPEEDER 86-3 RPW Standard Features
Automatic conveyor, rack type, single tank dishwasher with recirculating
pre-wash and wash and fresh water final rinse.
0.52 gallons/rack final rinse consumption
Capacity is 277- 20" x 20" racks per hour or 6,925 dishes per hour
CrossFire® Wash System provides superior cleaning
Wide insulated swing-out doors
Error proof replacement with color-coded curtains
Patented CrossFire® Wash System
Tank heat: 22.5 kW electric immersion heaters or steam injectors
Capillary thermometers for wash and rinse
In-line thermometer for final rinse
Vacuum breaker on all incoming water lines
Manifold clean-out brush
SureFire® Start-Up & Check-Out Service
Ventilation fan connection provision
S/S frame, legs and feet
S/S front enclosure panel
Automatic tank fill
S/S low water monitoring system
Detergent connection provision
Elevated top mounted NEMA 12 control panel
Easily-cleaned crowned hood top
Simplified scrap screen design
Door safety switch
Wide insulated swing-out doors
Standard frame drip proof motors
Override switch for de-liming
End caps/pipe plugs secured to prevent loss
Timing belt conveyor drive
Insinger SPEEDER 86-3 RPW Specifications
CONSTRUCTION- Hood and tank constructed of 16 gauge type 304 S/S. Hood
unit of all welded seamless construction. S/S frame, legs and feet. All
internal castings are non-corrosive lead free nickel alloy, bronze or
DOORS- Extra wide die formed 18-8 type 304 s/s front inspection doors hinged with S/S pins. A triple ply leading edge on the door channels made of S/S with no plastic or nylon sleeves or liners used. Door stop built into frame.
CONVEYORS- One S/S roller chain conveyor, with rack driving lugs every sixth link, running along the front of the machine. Fifteen free spinning rollers placed along the back wall of the machine. Conveyor accommodates all standard 20" racks. Conveyor drive system includes direct drive gear motor with frictionless, trouble-free clutch system, spring-loaded and automatically re-engaging. Racks conveyed automatically through washing and rinsing systems, powered by an independent 1/15 hp drive motor
PUMP- Centrifugal type “packless” pump with a brass petcock drains.
Construction includes ceramic seal and a balanced cast impeller on a
precision ground stainless steel shaft, extension or sleeve. All working
parts mounted as an assembly and removable as a unit without disturbing
pump housing. 1 hp motor for each wash and rinse pump: standard
horizontal C-face frame, drip proof, internally cooled with ball-bearing
CONTROLS- Top mounted NEMA 12 control enclosure, with 3.5 inch air gap
between hood and enclosure, housing motor overload protection,
contactors, transformers and all other dishwasher controls. All controls
safe low voltage 24 VAC.
ENERGY SAVER- Rack actuated lever automatically operates the final rinse
solenoid only when a rack passes, saving water and energy. The lever
also activates an adjustable timer control. If no ware passes during the
set time, the machine shuts down.
SPRAY SYSTEM- Spray arms made of type 304 stainless steel pipe. Spray
assemblies removable without the use of tools.
PRE-WASH- One manifold above and one manifold below, each with 3 high
pressure cleaning nozzles
WASH- Upper and lower manifolds with the patented CrossFire® Wash
System. One manifold above with 3 power wash arms, each with 9 high
pressure cleaning slots and one manifold below with 3 power wash arms,
each with 9 high pressure cleaning slots. The slots are precision milled
for water control producing a fan spray. Wash arms are fillet welded to
the S/S manifold. The CrossFire® Wash System provides 4 horizontally
spraying high pressure nozzles.
RINSE- Upper and lower manifolds. One manifold above with 3 power rinse
arms, each with 9 high pressure rinsing slots and one manifold below
with 3 power rinse arms, each with 9 high pressure rinsing slots. The
slots are precision milled for water control producing a fan spray.
Rinse arms are fillet welded to the S/S manifold.
FINAL RINSE- Six nozzles above and three nozzles below threaded into S/S
schedule 40 pipes. Nozzle assemblies produce a fan spray reducing water
consumption, maximizing heat retention
DRAIN- Drain valve externally controlled. Overflow assembly with skimmer
cap is removable without the use of tools for drain line inspection.
Heater is protected by low water level control.