EconAir 6919768 Exhaust Hood

4824EX2PSPF 12ft 0" Long ExhaustOnly Wall Canopy Hood with 16" Wide Front Perforated Supply Plenum with Builtin 3" Back Standoff x1 430 SS Where Exposed x1 Fire Cabinet on the Right Side 12.00" Width x 48.00" Length x 24.00" Height (Additional charges may apply for cabinet if not sold with fire system) x1 FILTER 20" tall x 16" wide KleenGard Stainless Steel Baffle Filter with Handles and Bottom Hanging Hook, UL Classified x9 Recessed Round LED fixture and LED Light, 3500 K warm output. x3 EXHAUST RISER Factory installed 16" Diameter X 4" Height x1 SUPPLY RISER 12" x 28" Supply Riser with Volume Dampers x3 1/ 2 Pint Grease Cup New Style, Flanged Slotted x2 BACKSPLASH 80.00" High X 156.00" Long 430 SS Vertical (Includes End Caps & Divider Bars) x1 Electrical Package Installation in Utility Cabinet by Plant. x1 RIGHT QUARTER END PANEL 23" Top Width, 0" Bottom Width, 23" High 430 SS x1 LEFT QUARTER END PANEL 23" Top Width, 0" Bottom Width, 23" High 430 SS x1 STRUCTURAL FRONT PANEL x1 Fire System #1 Job #6919768 TANKSP2 Tank Fire Suppression 8 gallon Fire System in Utility Cabinet (includes prepiped hood(s) with electric detection, tank(s), 24 VDC release mechanism, fire system agent, pressurized tanks, and electric pull station). (Formerly CASEWC). Includes piping for hood: 1. x1 Tankbased Fire Protection System equipped with Electronic Detection utilizing CORE board as a Listed Release Mechanism. Installed in Hood Utility Cabinet with integral hood prewire panel. x1 Pressure Switch Monitors Tank Pressure, Supervised Signal, TANK FIRE SUPPRESSION x1 SCEGVA11/ 2 GAS VALVE 11/ 2" Electrical Shutoff Valve for use with HMI reset, 110V, 60Hz (#8214275). Includes upstream strainer assembly. x1 Fan #1 EADU180H Exhaust Fan Job #6919768 EADU180H High Speed Direct Drive Centrifugal Upblast Exhaust Fan with, disconnect switch and 183/ 4" wheel. Exhaust Fan handles 2760 CFM @ 0.750" wc ESP, Fan runs at 1051 RPM. Exhaust Motor: 1.500 HP, 3 Phs, 208 V, 60 Hz, 6.6 FLA, ODP, Premium (EPlus3) Eff. x1 Grease Cup for kitchenduty centrifugal exhaust fans, Box Dimensions 171/ 8 L X 51/ 16 W X 33/ 4 H (20 Gauge) (Includes Down Spout) x1 SCEGVA11/ 2 GAS VALVE 11/ 2" Electrical Shutoff Valve for use with HMI reset, 110V, 60Hz (#8214275). Includes upstream strainer assembly. x1 Fire System #1 Total Price: $3,344.51 Fan #1 EADU180H Exhaust Fan Job #6919768 EADU180H High Speed Direct Drive Centrifugal Upblast Exhaust Fan with, disconnect switch and 183/ 4" wheel. Exhaust Fan handles 2760 CFM @ 0.750" wc ESP, Fan runs at 1051 RPM. Exhaust Motor: 1.500 HP, 3 Phs, 208 V, 60 Hz, 6.6 FLA, ODP, Premium (EPlus3) Eff. x1 Grease Cup for kitchenduty centrifugal exhaust fans, Box Dimensions 171/ 8 L X 51/ 16 W X 33/ 4 H (20 Gauge) (Includes Down Spout) x1 DU/ DR180HFA Gasketing Kit Thermeez Woven Ceramic Tape 1/ 4" x 1" with adhesive back Max Temp 1500°F. To be applied between fan base and grease duct. Installed under fan base 1/2" from the inside. Installed at the plant. x1 Curb CRB26.5x20E On Fan #1 Flat Curb x1 Hinged Base for Curb. Standard Hinge attached to curb. Used on Fans with wheels 20 inches or smaller. 12 GA Galvanized. x1 Vented Base for Curb x1 Full Bottom Curb Corner. Base flange corners fully welded or staked by factory. x1 Fan #2 EAA220D Supply Fan Job #6919768 EAA220D Untempered Supply Unit with 20" Mixed Flow Direct Drive Fan in Size #2 Housing Supply Fan handles 2400 CFM @ 0.500" wc ESP, Fan runs at 1001 RPM. Supply Motor: 1.000 HP, 3 Phs, 208 V, 60 Hz, 3.8 FLA, ODP, Premium (EPlus3) Eff. Down Discharge Air Flow Right > Left x1 Sloped Filtered Intake for Size #2 Standard Untempered MakeUp Air Unit with 12" blower wheel. 26.75" Wide x 29.25" Long x 31.5" High. Includes 2" MV EZ Kleen Metal Mesh Filters. x1 Down Discharge Construction for Size 2 Untempered Direct Drive AHUs x1 Motorized Back Draft Damper 22.75" X 24" for Size 2 Untempered Units w/Extended Shaft, Standard Galvanized Construction, 3/4" Rear Flange, Low Leakage, LF120S Actuator Included x1 Separate 120VAC Wiring Package for MakeUp Air Units. Option must be selected when mounting VFD in prewire panel or with DCV package. Provides separate 120VAC input to supply fan. This 120V signal must be run by electrician from DCV to mua switch. x1 Curb CRB31X20 On Fan #2 Flat Curb x1 Electrical System #1 Job #6919768 SC311110MA 3 Phase w/ control for 1 Exhaust Fan, 1 Supply Fan, Exhaust on in Fire, Lights out in Fire, Relay On/Off with Supply Fan, Fan(s) On/Off Thermostatically Controlled. Room temperature sensor shipped loose for field installation. INVERTER DUTY 3 PHASE MOTOR REQUIRED FOR USE WITH VFD. Includes 1 Duct Thermostat kit. x1 ESV751N02YXB571 Variable Frequency Drive 1 HP Max., 200/240 V, Single or Three Phase Input, 4.2 A Max., NEMA 1 Enclosure, with 2RJ45 FOR MODBUS 208v 1ph x1 ESV152N02YXB571 Variable Frequency Drive 2 HP Max., 200/240 V, Single or Three Phase Input, 7.0 A Max., NEMA 1 Enclosure, with 2RJ45 FOR MODBUS 208v 1ph x1 Digital Prewire Lighting Relay Kit. Includes hood lighting relay & terminal blocks. Allows for up to 1400W of lighting each. x1 Duct Run #1 430 Stainless (P1) EDW1645ASY Single Wall Duct 45 Degree Elbow, 16" Duct, Assembly. x1 (P2) EDW1645ASY Single Wall Duct 45 Degree Elbow, 16" Duct, Assembly. x1 (P3) EDW1647LT Single Wall Duct 16" diameter, 47" long, flange at both ends. Stainless Steel. x1 (P4) EDW1647LT Single Wall Duct 16" diameter, 47" long, flange at both ends. Stainless Steel. x1 (P5) EDW1648AJDKIT Single Wall Duct Adjustable, 16" diameter, 47.5" long, flange at one end With a 16" Adjustable Collar Stainless Steel. x1 (P6) EDW1618ADP13 Single Wall Duct Adapter, 16" Duct Dia to 18" Duct Dia, Assembly 430 Stainless Steel. x1 (P7) EDW2618TPDBEX Duct to Curb Transition 3/4" Down Turn, 26 1/2" Curb to 18" Duct, 16 GA Aluminized. Used on NCA16FA / NCA16HPFA & NCA18FA / NCA18HPFA. Transition Plate OD is 27.00" Designed For Use With Exhaust Fan. x1 3M2000PLUS Duct 3M Fire Barrier 2000 Plus Silicone Used as sealant to Seal Duct Joints. x2 735602000 Duct Duct insulation for zero clearance to combustibles 300" x 24" x 11/ 2" Roll. Unifrax FyreWrap Elite 1.5. x5 BANDING.5 Duct Fire Barrier Wrap Stainless Steel Banding .5" Width 200 FT Per Roll. x2 EDW16CLASY Duct "V" Clamp With new design 14 Ga Brackets, 16" Duct, Assembly. x6 SEAL.5050 Duct Fire Barrier Wrap Stainless Steel Banding Seal .5" Width. Quantity of 50. x2 TAPEALUM Duct Fire Barrier Wrap Aluminum Foil Tape 3" x 150' Roll. x1 Fire System Hookup: